TX5 – Rapid Curing Ceramic Epoxy Wearing Compound

TX5 – Rapid Curing Ceramic Epoxy Wearing Compound

Data Sheet

TX5 is a high-performance, ceramic-filled protective coating, formulated with 100% solids and reinforced by an advanced aramid fiber matrix to maximize durability under extreme abrasion and impact conditions. Completely free of solvents and engineered for fast curing, TX5 is ideal for industrial metal components exposed to harsh chemical agents like acids and caustics. Its smooth, non-slumping consistency allows for quick and effortless application by trowel or hand using latex gloves, enabling efficient repairs or full coatings up to 500 mils thick – even in facilities with minimal surface preparation and tight maintenance schedules.

Application Areas

Coverage

Color

Packaging

Technical Data

Maximum Temperature (Dependent on service) Wet Service | Dry Service 70°C | 93°C 158°F | 200°F
Solids by Volume 100%
Viscosity Paste
Mixed Density 2.0
Shore D Hardness (ASTM D 2240) 85
Pot Life 25 min / kg at 72ºF
SAG Vertical Resistance at 21ºC (70ºF) and 12.7 mm (500mils) No sagging
Mix Ratio 2:1 by Weight Base: Activator
Shelf life (unopened containers) 3 years at 55-95ºF (13-35ºC)

Application Sheet

Surface Preparation
Proper surface preparation is critical to the long-term performance of this product. The exact requirements for surface preparation vary with the severity of the application, expected service life, and the initial substrate conditions. All sharp edges and welds shall be ground smooth or to a 3mm (120 mil) radius before abrasive blasting. Optimum preparation will provide a surface thoroughly cleaned of all contaminants and roughened to an angular profile between 75-125μm (3-5 mil). This is normally achieved by initial cleaning and degreasing and then abrasive blasting to a cleanliness of Near White Metal, or by mechanical preparation.

Mixing
Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mixing board. Mix by Weight 2-parts Base to 1-part Activator. Mix thoroughly to produce an even colored and streak- free material. THINNING: Never thin.

Application
Use heavy plastic squeegee or putty knife to apply a 3mm minimum thickness. Work material into profile of substrate to achieve maximum adhesive and to remove any entrapped air. Contour to correct form with putty knife or plastic applicator. If mold or form is used be sure to coat its surface with a release agent to prevent adhesion of the material.

Application Temperature: Keep between 55 to 95ºF (17 to 35ºC). Substrate: keep between 45 to 105ºF (7 to 40ºC). the difference in temperature of the substrate and the material should never exceed 10ºF, 5ºC. Substrate shall be a minimum of 5ºF (3ºC) above dew point. Do not apply if relative humidity exceeds 90%. If necessary, heat the metal prior to surface preparation using electric heater or heat lamp. Never use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area overnight (75ºF+) for ease of mixing.

https://www.youtube.com/watch?v=WGkvDO7RbY0

Cured Time:

16°C (60°F) 25°C (77°F) 32°C (90°F)
Tack Free 45 min. 30 min. 20 min.
Light Load 1 hr. 45 min. 30 min.
Overcoat End 1 hr. 45 min. 30 min.
Full Load 1.5 hrs. 1 hr. 45 min.
Complete Chemical 4 hrs. 3 hrs. 2 hrs.

Clean 
Tools should be thoroughly cleaned immediately after use with a strong alkaline detergent.

Safety
Before using any product, review the Safety Data Sheet (SDS) or Safety Data Sheet for your area. Follow standard confined space
entry and work procedures, if applicable.

FDA Compliance
This product complies with FDA regulations: FDA 21 CFR 175.300 and FDA 21 CFR 175.105.

Download Product Data Sheet PDF


Download Safety Data Sheet PDF


The manufacturer, Taurus Epoxy Inc., makes no express or implied warranties, including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances shall the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability or any other theory arising from the use of this product. The information and recommendations contained herein are based on the Standard Product and are owned and provided solely for the use of our customers. This information is provided in good faith and is believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the conditions of use or the application process of the parts using this product, the manufacturer cannot accept responsibility for loss, injury or other damage resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no warranties of any kind, express or implied, are made by the manufacturer, Taurus Epoxy Inc., with respect to this, or any, product manufactured by them or any contracted or licensed manufacturer. Taurus Epoxy products do not provide structural integrity or improvements. They are only used to provide protection against corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in data sheets, data sheets, safety data sheets and any other information provided in writing directly from manufacturers’ technical support.