Logo Epoxy menu

TR9 RUBBER REPAIR COMPOUND

Data Sheet

Composed of elastomeric putty with good elongation, 100% solid, with filling of ceramic microspheres for rubber repairs. It is ideal for repairs of conveyor belts, pulleys and tanks with rubber coatings. It is easily applied trowel and spatula.

  • Applies up to 12.7mm without sagging
  • Extreme adherence on rubber, bronze, aluminum, concrete
  • For repair of belts, pulleys and coating rubber

Application Areas:

Coverage:

Packaging:

Technical Data

Maximum Temperature (Dependent on service)Minimum | Maximum-30°C | 93°C-22°F | 200°F
Elongation200%
Elongation Specific Gravity1,5
ViscosityLight Paste
Hardness of the Shore D Durometer93
ColorBlack
SAG Vertical Resistance at 21ºC (70ºF) 12.7mm (500mils)No sagging
Mixing Ratio9:1 by WeightBase: Activator
Shelf life (unopened containers)3 Years at 55-95ºF (13-35ºC)

Application Sheet

Surface Preparation
Proper surface preparation is vitally important for the long-term performance of Taurus TR9. The surface should be clean and rough. Prepare with mechanical cleaning with a rotating wire brush.
Clean with solvents (acetone, xylene, alcohol or MEK) and a cloth. It is not necessary to apply primer, Taurus TR9 is applied directly to the rubber or metal.

Mixing
Mix the activator well in the base with the mixing rod scraping the sides and the bottom of the container. Mix by weight 9 parts Base to 1 part of Activator. Mix thoroughly to produce a uniform and without stripes. Never put solvents.

Application
Use a heavy plastic brush or putty knife to apply a minimum thickness of 3mm. Work the material in the substrate profile to achieve maximum adhesive and remove any trapped air. Contour to correct the shape with putty knife material or plastic applicator. If mod is used or be sure to coat your surface with a release to prevent adhesion of the material.

Application Photo:

tr9-photo

Español

Cured time

16°C (60°F)25°C (77°F)32°C (90°F)
Tack Free2 hrs.1.5 hrs.1 hrs.
Light Load2.5 hrs.2 hrs.1.5 hrs.
Ready for 2nd Coat2.5 hrs.2 hrs.1.5 hrs.
Full Curated4.5 hrs.4 hrs.3.5 hrs.

Clean 
Use commercial solvents (acetone, xylene, alcohol, MEK) to clean tools immediately after use. Once cured, the material would have to be burned.

Safety
Before using any product, review the Safety Data Sheet (SDS) or Safety Data Sheet for your area. Follow standard confined space
entry and work procedures, if applicable.

Download Product Data Sheet PDF

Download Safety Data Sheet PDF

The manufacturer, Taurus Epoxy Inc., makes no express or implied warranties, including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances shall the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability or any other theory arising from the use of this product. The information and recommendations contained herein are based on the Standard Product and are owned and provided solely for the use of our customers. This information is provided in good faith and is believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the conditions of use or the application process of the parts using this product, the manufacturer cannot accept responsibility for loss, injury or other damage resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no warranties of any kind, express or implied, are made by the manufacturer, Taurus Epoxy Inc., with respect to this, or any, product manufactured by them or any contracted or licensed manufacturer. Taurus Epoxy products do not provide structural integrity or improvements. They are only used to provide protection against corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in data sheets, data sheets, safety data sheets and any other information provided in writing directly from manufacturers’ technical support.