Elastomeric putty compound with high elongation, hybrid-urethane, 100% solids, filled with ceramic microspheres for rubber repairs and is fully compatible for coating metals and other substrates. It is ideal for repairs on pulleys and tanks with rubber coatings. It is easily applied with a trowel and spatula.
For repair of belts, pulleys and coating rubber
| Maximum Temperature (Dependent on service) | Minimum | Maximum | -30°C | 93°C | -22°F | 200°F |
|---|---|---|---|
| Elongation | 200% | ||
| Elongation Specific Gravity | 1,5 | ||
| Viscosity | Light Paste | ||
| Hardness of the Shore D Durometer | 105 | ||
| Color | Black | ||
| SAG Vertical Resistance at 21ºC (70ºF) 12.7mm (500mils) | No sagging | ||
| Mix Ratio | 9:1 by Weight | Base: Activator | |
| Shelf life (unopened containers) | 3 Years at 55-95ºF (13-35ºC) | ||
Surface Preparation
Proper surface preparation is crucial for the long-term performance of Taurus TR9P.
The surface must be clean and rough.
Prepare using mechanical cleaning with a rotary wire brush.
Clean with solvents (acetone, xylene, alcohol, or MEK) and a cloth. It is not necessary to apply a primer, as Taurus TR9P is applied directly onto rubber or metal.
Mixing
Thoroughly mix the activator into the base using a mixing rod, scraping the sides and bottom of the container. Mix by weight, 9 parts Base to 1 part Activator. Mix thoroughly to produce a uniform, streak-free material. Never add solvents.
Application
Use a heavy-duty plastic brush or putty knife to apply a minimum thickness of 3mm. Work the material into the substrate profile to achieve maximum adhesion and eliminate any trapped air. Shape the contour using a putty knife or plastic applicator. If using a mold or form, make sure to coat its surface with a release agent to prevent material adhesion.
Cured Time:
| 16°C (60°F) | 25°C (77°F) | 32°C (90°F) | |
|---|---|---|---|
| Tack Free | 2 hours | 1.5 hours | 1 hour |
| Light Load | 2.5 hours | 1.5 hours | 1 hour |
| Ready for 2nd Coat | 2.5 hours | 1.5 hours | 1 hour |
| Full Curated | 2.5 hours | 2 hours | 1.5 hours |
Clean: Tools should be thoroughly cleaned immediately after use with a strong alkaline detergent.
Safety: Before using any product, review the Safety Data Sheet (SDS) or Safety Data Sheet for your area. Follow standard confined space
entry and work procedures, if applicable.
FDA Compliance: This product complies with FDA regulations: FDA 21 CFR 175.300 and FDA 21 CFR 175.105.
The manufacturer, Taurus Epoxy Inc., makes no express or implied warranties, including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances shall the manufacturer be liable for incidental, consequential or other damages, breach of warranty, strict liability or any other theory arising from the use of this product. The information and recommendations contained herein are based on the Standard Product and are owned and provided solely for the use of our customers. This information is provided in good faith and is believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the conditions of use or the application process of the parts using this product, the manufacturer cannot accept responsibility for loss, injury or other damage resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no warranties of any kind, express or implied, are made by the manufacturer, Taurus Epoxy Inc., with respect to this, or any, product manufactured by them or any contracted or licensed manufacturer. Taurus Epoxy products do not provide structural integrity or improvements. They are only used to provide protection against corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in data sheets, data sheets, safety data sheets and any other information provided in writing directly from manufacturers’ technical support.